About this 3D model

SUPPORT FRAME FOR MOBILE TABLET Based on support for tablet car, created a portable version, with some modifications. The project was developed atravéz my tablet a Nexus7 with dimensions of 195x120mm. I found great support and comfortable to hold in handling the tablet version for car, s why I decided to develop another in portable mode. Introduced some innovations, such as a handle to leave the tablet in three positions: the first standing vertically, inclined to watch other videos and another position more inclined for typing. The highlight is the system fit between the two parts of the frame top and bottom. In the top frame consists of two pins and a protrusion projetadada down on the back, which fits into a cavity of the bottom frame. And so, joining the two parts of the frame atravéz that dock, it forms a single frame of the tablet. This same operation docking of two frames, there is also the locking handle, whose head consists of three holes at different angles, with the goal of leaving the frame in three different positions. For that reason they, together with the engaging part of the upper frame, on both sides there are two pins that fit into holes in the head of the handle. For completeness, there are two shields located on both sides of the bottom of the frame to fix the handle. Definitavamente This prevents the handle coming loose from the frame. Thus, in any position one wants to let the frame, the lock mode is to attach the top frame in the frame bottom atravéz existing at the rear of the housing, while the side pins fit into the holes in the head strap , tr avando it. To better understand how the whole frame assembly with the support, in the figure (Img16) think each piece is identified by the numbers, and the whole thing is made up of three main parts, and two pairs of complementary pieces as descriptive below : 1 - Frame top that fits on the bottom frame, atravéz of a part designed for low (8) and has a drawer in this fitting (9) to hold the headset. 2 - Frame below, supplemented by the upper frame, atravéz fitting (6), connected with the handle (03) to secure the assembly in different positions, atravéz pin (05) located on the sides. 3 - Handle mobile revolving frame connected by lower atravéz pin located in lateriais this, allowing atravéz your position turning the set in three different positions, being fixed atravéz holes located in its head, which fits and fixed pins ( 5) at the bottom of the top frame. These main parts are complemented atravéz other auxiliaries, such as bulkhead (4), which gives support to handle, preventing it from loosening, and the pin (5), which should be metallic. This may be a nail cut to size 5x14mm, as has been done. With respect to the pins on the sides of the bottom, which connects with the handle, and also the side-pins will be produced directly from the pieces, but left a hole in them, to be preencidos epoxy putty or metal pin, in order to reinforce this point. See the image (img11, 12) Besides this function to let the tablet in various positions, can also serve to guard it while being carrying, simply turn to the screen in the opposite direction, so that the screen is protected. In the original design, which was produced in Makerbot, presented several imperfections like warping and cracking. Also the pin that fits into the holes broke, besides the holes located at the head of the handle come out deformed because they were muitojuntos because I designed for four positions. Fix all cracks and warping, atravéz of epoxy putty, and redid the holes with this mass, reducing to three positions (See iImg8 9:10). The pin that connects the handle to the bottom frame, put metallic. Then spray painted with acrylic blue. Among the changes I made from the corrections I made in the original design, I added two screens on the sides of the frame to support the handle, but the biggest change was the introduction of a drawer to hold the headset, located at the top of the frame, that fits in the bottom. This niche for headset did like another support for smartphone and tablet. See the image (Img15). Increased their estensão and thickness so that it could be possible. As my projects are characterized by being functional, s why the pieces are a bit complex, they sometimes come with imperfections printer, s why it is necessary to make corrections and adjustments. Because of this, you need to have some tools, like a micro drill with all accessories that I consider indispensable, sandpaper, epoxy putty, glue instantly, pliers, spray paint, etc.., As seen on the image (Img07). I also made available the files in Makerware ready for the parts being produced at positions I found the best fix Makerware. My Makerbot is in trouble. I am not able to connect more with the computer, s why, did not yield to produce the modified project, depending on the changes I made. For that reason they, if they can send me the picture frame assembly, when they have done in their printers. Then