About this 3D model
Summary Penguin by the Anchor Human rarely hunted penguins directly, but slowly starved them to death. Commercial large-scale capture of krill had made penguins to face undernourishment. Businessmen capture them for the rich krill omega-3s! Krill is the basis of the Antarctic food chain, including emperor penguins, Adelie penguins, blue whales, and various albatrosses feed on krill. If there’s no krill at the south Pole, the natural ecosystem will be collapsed and penguins will be the biggest victim! The research team believes that industrial-scale capturing is one of the greatest threats to krill in Antarctic ocean. If commercial practices of krill are not stopped, the number of penguins in the near future may be reduced by 1/3. In fact, we don’t need to grab the penguins’ food because omega-3 is widely found in human daily, such as fish, nuts, seaweed, etc. Do not be deceived by the commercial interests and the gimmicks! Do not buy krill products! It's not your health that you spend money on, but poor and helplessness for the lives of the penguins. The design of this penguin has been completed for some time. When I learned about the crisis facing by the penguins, I hope people pay attention to this matter and reminded by my work! I then designed an ice floe with anchors hanging to clearly understand that the penguins have been invaded excessively by human. When you print this work and share the printed results, please remember to use your anchored ice floe to tell your friends that penguins in the Antarctic ocean are facing human damage! Thanks SpiderMaker for sponsoring the creation of this work https://www.3dspidermaker.com/ https://www.facebook.com/groups/3dspidermaker/ Material used: SpiderMaker PLA Matt black, extinction white, orange, warm white, original leather Design Software: SketchUp PRINT UP+ & CR10 Printing Recommendation Height: 0.2mm Support Type: None Not less than 0.75 and increase the resolution to 0.15mm when downsize printing (ps. Because the accuracy on the printer is not the same. If the assembly parts are too loose or too tight, the parts may be reduced or enlarged to offset the assembly failure caused by the printer's tolerances.) https://www.facebook.com/paperworkers https://amaochan.work/work/ Penguin by the Anchor Humans rarely hunt penguins directly, but they slowly starve them to death. Commercial large-scale krill harvesting causes penguins to face food shortages. Businesses extensively harvest krill, citing its rich omega-3 content. Krill is the foundation of the Antarctic food chain, with emperor penguins, Adelie penguins, blue whales, and various albatrosses all feeding on it. Without krill, the Antarctic's natural ecosystem will collapse, and penguins will be the biggest victims. The research team believes that industrial-scale harvesting is one of the greatest threats to krill in Antarctic waters. If such commercial practices of krill harvesting are not halted, the penguin population may decrease by one-third in the near future. In fact, we do not need to take food away from penguins, because omega-3 is widely found in everyday human foods such as fish, nuts, seaweed, and so on. Do not be deceived by messages and gimmicks hyped by commercial interests. Do not purchase krill products. What you are paying for is not your own health, but the lives of helpless and pitiful penguins. The design of this penguin was completed some time ago. When I learned about the crisis facing penguins, I hoped to use this work to raise awareness. Therefore, I designed an ice floe with an anchor attached to clearly convey that humans have excessively encroached upon the penguins' habitat. When you print this work and share your prints, please remember to use this anchor-bearing ice floe to inform your friends that penguins in the Antarctic waters are facing human-inflicted harm. Thanks to SpiderMaker Weaver for sponsoring the creation of this work Materials used SpiderMaker PLA Matte black, Matte white, Sun orange, Warm white, Original leather color Design software SketchUp Printing UP+ & CR10 Printing Recommendation Layer height 0.2mm No supports When scaling down, please do not go below 0.75 and increase the resolution to 0.15mm (ps. Due to variations in printer accuracy, if assembled parts are too loose or too tight, individual parts can be scaled down or enlarged to compensate for assembly issues caused by printer tolerances.) https://www.youtube.com/watch?v=X0OFBxcySy4 Print Settings Printer Brand: Up Printer: Up Plus Rafts: No Supports: No Post-Printing