About this 3D model
NOTICE: REMIX ARE NOT ALLOWED NOTICE: DO NOT POST ANY OF YOUR PROFILE I design this a purge chute cover with a silicon nozzle wiper. Benefits: Purged filament doesn't jump on the plate Nozzle is better cleaned Pieces of purged filament don't go everywhere , each corner of the printer remains clean How to install THE MODELS WITH and WITHOUT THE LOGO: How it works: INSTRUCTIONS What is the nozzle wiper made of? It is made from a piece of silicone from the molds used to make pancakes. Like this one you see in this pic: How big should the silicone piece to be cut be? 10mm x 2mm x 15mm PRINT THE POOP STOP WITH THE NOZZLE WIPER CUT THE PIECE: APPLY THE SILICON PIECE IN THE SEAT OF THE POOP STOP AND INSTALL THE POOP STOP IN THE POOP BUCKET AS YOU SEE IN THIS PIC , MY MODEL IS SUPER FLAT, SO WARPING MUST BE ON IT TO AVOID CRASHED OR SCRATCHES AGAINST THE HOTEND, TOOLHEAD OR FAN DUCT: BE SURE WHEN YOU'RE PRINTING , THE PRINT IS NOT WARPING!! With what materials should it be printed? I recommend PAHT-CF and PET-CF. This is because, when the printer is performing the "nozzle cleaning tip" function, the nozzle temperature is 200°C. So I recommend printing it with materials that resist high temperatures to avoid deformation or future problems. Do you want to use ABS? Ok, you're free to do so, but don't give me a bad rating for YOUR CHOICE! I have tested this model so many times and it works smoothly! No issue. ALL THE MODELS ARE AVAILABLE ON MY PAGE. NOTICE: DON'T MODIFY THE ORIENTATION! NOTICE: THE FOLLOWING PHOTO SHOWS THE EXTRUDED FILAMENT BEING HELD ON THE SILICON NOZZLE WIPER, BEFORE PRINTING. THIS IS ONE OF THE MAIN REASONS WHY I DESIGNED THIS MODEL. THAT EXTRUDED FILAMENT COULD RUIN YOU FIRST LAYER! PLEASE CHECK ALWAYS IF THE SILICON NOZZLE WIPER IS CLEAN AND IF YOU SEE THAT SOME EXTRUDED FILAMENT HAS BEEN DEPOSITED ON IT, REMOVE THE EXTRUDED FILAMENT AND ENJOY 3D PRINTING. THE PHOTO WAS MADE AS EXAMPLE AFTER 3h PRINTING. MY MODEL HAS ALREADY BEEN TESTED, FOR A MONTH AND I DON'T FIND ANY PROBLEMS. THE MODEL ,AS TEST EXAMPLE IN THE PIC, WAS PRINTED IN ABS, BUT I STILL RECOMMEND SUPERIOR FILAMENTS LIKE PC , PATH OR PET. ??????: ???? ?? ? ?????? ?????. ?? ??? ??? ?? ??? ???????? , ?? ????? ????? ???? ???? ?? ??? ???. ?? ?????? ??? ???? ??? ?????? ?? ?? ????????, ?? ???? ??? ???? ? ???? ??? ???????? ??? ??? ?? ???????? , ??? ??? ???'? ???? ? ???? ??? ????????. ? ???'? ???? ?? ?????? ? ??? ?? ???????? ??? ???? ?????? ??????? ??? ???? ??? ??? ????? ?????? ?????! ???? ??? ???? ?? ????? ??? , ?? ?????'? ???? ????? ??? ??? ?????? ????? ??????! ??????, ???? ? ???? ??? ????? ?????? ?? ??? ??? ????! ??? ?????? ???????? ??? ????? ??? ???? ??? ?? ????? ????? ????? ?? ??? ?????! ????? ??? ??? ??? ?????????????! ᴵᶠ ʸᵒᵘ ʰᵃᵛᵉ ᵖʳᵒᵇˡᵉᵐˢ ᵃᵇᵒᵘᵗ ᵗʰᶦˢ ᵐᵒᵈᵉˡ, ʲᵘˢᵗ ˢᵉⁿᵈ ᵐᵉ ᵃ ᵖʳᶦᵛᵃᵗᵉ ᵐᵉˢˢᵃᵍᵉ ᵃⁿᵈ ᴵ'ˡˡ ʰᵉˡᵖ ʸᵒᵘ. ᴳᶦᵛᵉ ᵐᵉ ᵃ ˡᶦᵏᵉ ᵃⁿᵈ ᶠᵒˡˡᵒʷ ᵐʸ ᵖᵃᵍᵉ. ᵀʰᵃⁿᵏ ʸᵒᵘ ᵗᵒ ˢᵘᵖᵖᵒʳᵗ ᵐᵉ ᵃⁿᵈ ʰᵃᵖᵖʸ ᵖʳᶦⁿᵗᶦⁿᵍ.