About this 3D model

This version is a remix from the 2019 original from Thingiverse. https://www.thingiverse.com/thing:2786671/files I made an effort to upgrade and remix it cause I Think this is easy, and far away, the best Y-Tensioner Mod for prusa. Only one bolt to adjust tension. See the Complete Install Guide below this info!!!! Dont miss it !!! Compatible With: __________________________________ Prusa Mk3 Prusa Mk3s Prusa Mk3s+ Other Printers Upgrades: __________________________________ Hex holes are tight, hex nuts dont fall off when you are installing the mod. LockNuts dont turn inside the hole when you are aplying tension. Block-TNuts and M3 Hex Heads are HIDDEN inside the frame (for better looking) New Y_Holder with improved Height and door to assure the Gt2 belt Alternative Y_Holder from Jackass Filament ( https://www.printables.com/model/205812-prusa-mk3-y-belt-holder-improved-for-gates-belts/files ) Y-Holder has 48mm width (for compatibility with Mk3S Y-Motor Mount ultra and other mods) Mk3 Y Belt Holder inside collection for alternative Y-Holder (print the one you most like) Original Features: __________________________________ The mod has paralelism across all the belt. Is easy to print and install Can be used with other mods Original GT2 Belt can be used Hardware Needed: __________________________________ 2 M3x35mm socket head cap screws (for idler_Frame and Mount) 1 M3x30mm socket head cap screws (for tensioner) 2 M3x10mm for Y_Holder 5 M3 Nylock nut (For idler_Frame and Mount) Your Pulley What files to print? __________________________________ 1x Base Holder 1x Base_for_your_pulley (GT2, GT16, Prusa Version, etc) 1x Y Holder (this version or another) Compatible Mods __________________________________ Y-Axys Motor Mount Ultra ( https://www.printables.com/model/57937-mk3s-y-axis-motor-mount-ultra ) MK3 Y Belt Holder ( https://www.printables.com/model/205812-prusa-mk3-y-belt-holder-improved-for-gates-belts/files ) _________________________________________________________________________________ INSTALL MANUAL _________________________________________________________________________________ 1º - Prepare the Base_Holder 2º - Insert the LockNuts into the Hex Holes. Dont worry if you cant, its thight. Use the Pull method from the Prusa manual and screw them :) 3º - Get the “Base_for_your_pulley” (I choose the Prusa one) 4º - Put It in the Base_Holder. Later will be screwed 5º - As you can see , the Base_of_Your_pulley has two sides. One with Hex Holes, One with Round holes. 6º - Prepare your Pulley, two M3x35 and Two LockNuts 7º - Put the LockNuts in the Hex holes! Now , from the other side, Insert the M3 across the BaseHolder + Base_of_Your_pulley + Your Pulley. Screw a little , dont be rude. The Y base needs to move freely, and your pulley too!!! 8º - Now Prepare a m3x30 and another Locknut. Put it in the hex hole. Screw from behind. 9º - You will end with something like this! 10º - Time to pass the Belt across our Tensioner. 11º - Now pass the belt into the Bed-Holder Too, as shown in this image. Is easy in this step. 12º - Pass the rest of the gt2-belt across the motor and put it into the Bed Holder. You can now use 2x m3x10 bolts to screw the Bed-Holder to the Bed.. Optionally, you can put the Bed-Holder-Door to assure your GT2 BELT with 2 M3x18 and two hexnut or locknut. 13º - You will end with a tensioner like this one. Only one bolt to add or rest tension to the Y-Axis. You can do it from the FRONT of the printer, even if the LCD screen is in his place :) ENJOY!