About this 3D model

BEHOLD! THE INCREDIBLY not-so-large TOME FOR PLAYING DUNGEONS AND DRAGONS! Now, before you get all excited, I highly recommend you read the ENTIRE description (with some exceptions) before starting your prints, just to be sure you don't have any regrets. (Who knew you'd be reading a tome in order to print a tome?) Various inserts for the tome are available. Disclaimer: The design was inspired by a friend who asked if I could make a D&D book for her to gift to someone. She knew nothing about D&D and neither did I. So I did some research and spoke with individuals who have played the game to get some ideas of what one might like in a tome like this one. So, if you have any feedback at all or any ideas on how the design can be improved or any additions that I could add to the book, please share! There will be a good chance you'll see some welcome changes if you do. When specifying dimensions, they will be stated in terms of width x height x depth Features: Inserts for this tower were designed with "units" in mind so individuals can remix inserts according to their desires (Similar to gridfinity, but with different dimensions). Each unit is 30.5x30.5x25.2mm. So if I made a 1x1x1 insert, it would occupy 30.5x30.5x25.2mm. Note: Make sure to incorporate tolerances when remixing inserts. I usually add a 0.2mm tolerance to each side, so the true measurement of a 1x1x1 insert for me would be 30.1x30.1x24.8mm. This model includes models for a dice tower that magnetically attaches to the book cover (See images for details). The dice tower was designed to fit in the tome in two different orientations. When folded, it will occupy a space of 4x3x2 units. When open, it will occupy a space of 4x6x1. The dice tower includes a door that opens to ensure dice land in the book and not on the floor (See images for details). About the Hinge Links: The tolerance of where the hinge links clip into the book/dice tower are VERY tight. This is on purpose to ensure there isn't a lot of wobbling when opening and closing the book and helps to ensure longer durability of the hinge mechanisms. However, because of the way they were designed, you can scale them if you find the default thickness of them is too difficult to get snapped in. Just be sure to only scale them on the Z axis. Lower tolerance hinge links have been provided in case you feel iffy about scaling them. If you don't have man-hands like me, you might consider printing the lower tolerance hinge links for both the book hinge and the dice tower hinge. You should still get a nice fit. Because of the way the hinge links were designed, if they wear out or get too loose, you can easily print new ones and replace the old ones. You'll notice on one end of the hinge links, the hole is incredibly small. This is on purpose. The small hole is only 0.2mm thick before changing to the diameter that you see on the other side. I've found, when the plastic deforms when connected, it hugs the little "pins" and helps keep the hinge link from rattling. I've found this gives the book a more smooth and sturdy feeling when opening and closing it. If you're printing with something other than PLA, you might want to consider changing the link slightly according to your needs. Printing Instructions: Required Hardware: 24 - 6x3mm magnets (Yes, you'll need 24 of them... lots of magnets. Fortunately, you can usually buy a pack of 50 or 100 for $5-$10) Supports? NEVER! GO TO HELL! Brim: Recommended for all parts to avoid warping. All models should be oriented in the way they were intended to be printed. What to print: Book Front Cover - x1 Book Back - x1 Book front Hinge Interface - x1 Pages - x1 Long Hinge Link - x2 Short Hinge Link - x2 Optional dice tower: Dice Tower Part1 - x1 Dice Tower Part2 - x1 Dice Tower Hinge Link - x2 The 3mf file provided was sliced in OrcaSlicer and has recommended configurations for printing each piece of the main tome. The dice tower included in this model is slightly different from the one included in the master tome. The one included with this model doesn't have a door as it doesn't need one to guide dice into the main part of the book. Assembly: Video Instructions All magnets should have a press fit tolerance. However, because of the different variations of printers out there, you may find you need to glue yours in or you may have to use brute force. Note: When installing magnets, be extra sure you're installing them in the proper orientation so they attract each other. I've made mistakes and don't want you to repeat them. The Book Front Hinge Interface is meant to be glued into where the book binding would be on the front cover. It's designed so, if you try to place it incorrectly, it won't fit right. (I'm considered implementing some sort of fastening implementation to attach the hinge interface to the front cover. So if that's one of your gripes, stay tuned). Glue the pages onto the book back. When snapping in the hinge links, it is recommended that you snap the hinge li