About this 3D model

Pack Includes Magnetic Honey Bee Magnetic Beehive Tree for Beehive Honeyjar Printing Notes For Fellow Makers (Please Read Carefully) : ? Captive Magnet Slots: Both The Bees And The Beehive Feature Hidden Captive Magnet Slots, Keeping Magnets Out Of Sight While Making The Entire Setup Sleek And Efficient. ? Seamless Beehive Printing: The Beehive Is Split Into Two Parts To Allow For Clean And Even Printing Without Sacrificing Quality. Once Printed, Both Halves Can Be Glued Together Using The Aligner, Giving It A Smooth, Uninterrupted Look From Top To Bottom, No Seams. ? Display Tree Included ( In 3 Parts to Speed Up Printing !!!) ? The Tree Is Split Into Three Separate Parts: The Trunk, Branch, And Flowers. This Makes For Faster, Cleaner Prints. You Can Print Each Part Separately And Glue Them Together, Then Attach The Finished Beehive Directly To The Tree For A Complete And Charming Display Setup. ? Seamless Assembly: After Printing, The Two Beehive Parts Can Be Glued Together Using An Internal Connector/aligner, Creating A Seamless Finish From Top To Bottom. ? Magnetic Versatility: The Bees Have Captive Magnets Too, So They Don’t Just Stick To The Hive, They’ll Happily Cling To Any Metal Surface. Even Your Fridge Just Got A New Favorite Visitor. ?? ? The Beehive Can Hold Up To 12 Magnets In Total, 6 In Each Half, Providing Strong, Even Magnetic Force Across The Entire Structure, (No Matter Where you Place the Bee). ? Supports 10x3mm Magnets The Bees And Beehive Are Designed Specifically To Fit 10x3mm Magnets And Are Pre-Scaled To Accommodate Them Perfectly. You Can Scale The Model Up Slightly If Needed—But Scaling Down Is Not Recommended, As It May Affect Magnet Fit for 10x3mm Magnet. ? Added Pause For Bambu Printers For Bambu Printer Users, I’ve Added Preset Pause Points Where You Can Easily Drop In Your Magnets Mid-Print, no Extra Editing Needed, ? Magnet Orientation (Please Read Carefully) : ⚠️ To Ensure Proper Magnetic Attraction: All Magnets Inside The Beehive Must Face The Same Direction, Either All North Or All South Facing Outward. Just Be Consistent. Then, The Magnets Inside The Bees Must Face The Exact Opposite Pole Of The Hive Magnets. ➤ For Example: If Hive Magnets Face North Outward, Bee Magnets Should Have South Facing Downward. ⚠️ Incorrect Polarity Will Cause The Magnets To Repel, And The Bees Will Refuse To Stick !!! ? My Bambu Settings & Suggestions Using Bambu X1C :- Wall Count- 4 For Maximum Strength / 3 For Beehive Layer Height- 0.2mm Minimum Downscaling- Not Recommended Outer Brim- On (For Maximum Adhesion) You May Keep The Brim OFF If You're Using a Textured PEI Plate or BIQU Cryogrip/Frostbite Plate Adaptive Layer At Max - Recommended For Single-Color Prints For Better Quality Specially When Printing Smaller. However, For Multicolor Prints, Adaptive Layers May Significantly Increase Print Time. Rest Of The Settings- Defaults Bambu 3MF Files Included For Bambu Freaks ? !! -TikTok- tiktok.com/@printverse_designs-Instagram- instagram.com/printverse_crafts-Twitter- twitter.com/Printverse1 The Printverse Designs are protected by Copyright Law. When you purchase, You Do Not have the right to sell any digital file or printed model without any consent You can obtain commercial licence to sell physical Prints from this link - patreon.com/printverse Thank You !!!