About this 3D model

This is a detailed T.A.R.D.I.S. lamp which uses the LED Lamp disk available from the Bambu Lab store . This famed TARDIS from Doctor Who stands just over 17cm tall when built and (whilst it helps and may improve quality), can be printed almost as pictured without an AMS (with the exception of the sign on the door). Prefer a multi-material verision? An AMS friendly multi-material version is also available here 0.2mm and 0.4mm nozzle versions I have also included two versions of both the sign on the door, and the signs at the top, one version that is compatible with a standard 0.4mm nozzle, and one version which uses the finer detail capable with a 0.2mm nozzle allowing for a more accurate representation of the actual TARDIS. The simplfied 0.4mm top sign however can be printed multi-colour without an AMS, just print it face down, with the first layer black, and the rest white. Update: I've uploaded an additional profile which includes the more detailed top signs which are designed for printing with a 0.2mm nozzle, but if printed upright, you can actually still print them with a 0.4mm nozzle. It is worth noting though that whilst this full detail top sign can be printed with a 0.4mm nozzle in this orientation, it will require an AMS. If you can only print with a 0.4mm nozzle and don't have an AMS (or other multi-material setup), please use my simplified top sign. You can see in these pictures I'm holding the 0.4mm versions next to the 0.2mm versions which are fitted to the Tardis: Three Top Sign Versions Comparison: 0.2mm Top Sign 0.4mm Top Sign Detailed 0.4mm Top Sign Profile Location Detail Parts for 0.2mm Nozzle All Parts Detailed Top Sign (0.4mm) STL Name Top Sign.stl 4.0 Top Sign.stl Top Sign.stl Orientation Face down (text against bed) Face down (text against bed) Upright (printed on long thin edge) AMS Required Yes No Yes Nozzle Size Required 0.2mm 0.4mm 0.2mm or 0.4mm Photo Two Door Sign Versions Comparison: 0.2mm Door Sign 0.4mm Door Sign Profile Location Detail Parts for 0.2mm Nozzle All Parts STL Name Door Note.stl 4.0 Door Note.stl Orientation Face down (text against bed) Face down (text against bed) AMS Required Yes Yes Nozzle Size Required 0.2mm 0.4mm Photo The Parts Explained As I've designed this to be printable with or without an AMS, there are quite a few parts and I'll explain each of them below: 0.4 Door Note - This is the sign for the door simplified to allow printing with a 0.4mm nozzle 0.4 Top Sign - This is the sign at the top of the TARDIS saying “POLICE BOX”, simplified to allow printing with a 0.4 mm nozzle. This should also be printable without an AMS by printing it face down, printing the first layer in black, and then switching to white from the second layer.You'll need 4 of these. Base Cap - This screws into the base to hold the LED lamp in place once fitted Door Handle - This is the main door handle. It can be printed with a 0.2mm or 0.4mm nozzle, but if you're using a 0.2mm one for the signs anyway, print this with them as you'll get better detail with that. Door Note - This is the sign for the door designed to be printed with a 0.2mm nozzle Key Hole - This is the keyhole on the door. It can be printed with a 0.2mm or 0.4mm nozzle, but if you're using a 0.2mm one for the signs anyway, print this with them as you'll get better detail with that. Light Cap - This is the blue cap that sits on the top of the light columb on the top of the TARDIS. This should just push fit onto the light. Mini Door Handle - This is the slightly smaller handle which sits next to the sign on the door. It can be printed with a 0.2mm or 0.4mm nozzle, but if you're using a 0.2mm one for the signs anyway, print this with them as you'll get better detail with that. Reflector - This fits to the underneath of the lid and is designed to reflect the light shining up from the LED disk outwards onto the windows. You'll want to print this white unless you wanted to tint the colour of the light that hits the windows. Reflector screw - This screws down into the reflector and then the other side into the base of the lid Tardis Body - This is the bulk of the Tardis body. This requires some support material at the bottom for where the LED light is fitted Tardis Lid - This is the top part of the Tardis, and the only other part that requires support material. Top Light - This is a thin white column which pushes into the top of the lid Top Sign - This is the sign at the top of the TARDIS designed for printing with a 0.2mm nozzle. I don't believe this version will print without an AMS. You'll need 4 of these Window Inserts - These are the windows which slot in on the inside of the body. You'll need 8 of these. Assembly Instructions Once everything is printed follow the steps below. Please note, much of this will just push-fit and clip into place, but some parts such as the door handles, keyhole, and possibly the windows, may require the tiniest dab of glue to nicely fix them in place. Step 1 Take the reflector screw, and s