About this 3D model

This is a remix of the Prusa Mk3 version. I use this system on my Prusa and I have not found an equivalent for the Sidewinder, so I made an adaptation ^^ These are 24V LEDs, connected directly to the power supply on the free pins. I only use it to check my current prints, the LEDs are not on for several hours. I created a notch on the files in order to lower the cable to the right or to the left towards the power supply. I added a switch at the bottom of the right arm (super easy access). I haven't checked yet, but I think we can use the full height of the print. The support does not interfere if you have added a triangulation from the back like I did. You will need supports for the fixing paste. I am also enclosing the cover of the U-profile, personally, I did not use it because it illuminates better without, but for an aesthetic side, I can understand that some want to add it, I had done it for my prusa, so I think it should work on this model as well, I just enlarged it (32.5cm). If you print it, I advise you in white or transparent Files: Prusa MK3 model: https://www.prusaprinters.org/fr/prints/3267-led-light-bar-prusa-i3-mk2mk3 Switch housing: https://www.prusaprinters.org/fr/prints/18478-artillery-sidewinder-x1-led-top-extrusion U-Profile (32.5 cm for the Sidewinder): https://www.prusaprinters.org/fr/prints/54526-led-u-channel-9x17mm Cable passage profile: https://www.prusaprinters.org/fr/prints/30734-20202040-extrusion-cover-cable-channel Purchases: Led 24v: https://www.amazon.fr/gp/product/B07L5QRPVZ/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1 Switch: https://www.amazon.fr/gp/product/B076GXD7XN/ref=ppx_yo_dt_b_asin_title_o05_s01?ie=UTF8&psc=1 → if you have any questions, do not hesitate ;) ____________________________________________________________ This is a remix of the Prusa Mk3 version. I use this system on my Prusa and I have not found an equivalent for the Sidewinder, so I made an adaptation ^^ These are 24V LEDs, connected directly to the power supply on the free pins. I only use it to check my current impressions, the LEDs are not on for several hours. I created a notch on the files in order to lower the cable to the right or to the left towards the power supply. I added a switch at the bottom of the right arm (super easy access). I haven't checked yet, but I think we can use the full height of the print. The support does not interfere if you have added a triangulation from the back like I did. You will need supports for the fixing paste I am also enclosing the cover of the U-profile, personally, I did not use it because it illuminates better without, but for an aesthetic side, I can understand that some want to add it, I had done it for my prusa, so I think it should work on this model as well, I just enlarged it (32.5cm). If you print it, I advise you in white or transparent Files: Prusa MK3 model: https://www.prusaprinters.org/fr/prints/3267-led-light-bar-prusa-i3-mk2mk3 Switch housing: https://www.prusaprinters.org/fr/prints/18478-artillery-sidewinder-x1-led-top-extrusion U-Profile (32.5 cm for the Sidewinder X1, joint here): https://www.prusaprinters.org/fr/prints/54526-led-u-channel-9x17mm Cable entry profile: https://www.prusaprinters.org/fr/prints/30734-20202040-extrusion-cover-cable-channel Purchase: Led 24v: https://www.amazon.fr/gp/product/B07L5QRPVZ/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1 switch: https://www.amazon.fr/gp/product/B076GXD7XN/ref=ppx_yo_dt_b_asin_title_o05_s01?ie=UTF8&psc=1 → if you have any questions, do not hesitate