About this 3D model
Slider version now live and available Test prints have been successful and are now good to go. If you encounter any issues please let me know! still working on the minor accessories to match the sliding version as it was a complete model rebuild to accommodate them into the old/previous model (will be released in the corresponding folder here) Adapting a backplate mechanism to help secure it onto the P1P as they don't have a stable way to attach to the top Testing of 2812B LED strips with a BT 5v usb adapter and connectors or seperate power supply unsure of which will work best adapting the Backer into a more robust case enclosure (near future design) Print File Options: (both will fit together) Note: These will effect the top slotting for LED width, the interior walls will also be different but they will all connect together and not compromise the outside fit/look Narrow: (N) has a 12mm Top Interior Clearance - Available Now Wide: (W) has a 16mm Top Interior Clearance - Available Now (LED portions are coming ASAP) (W) v3_2 had wider LED channels then the v3_1 to allow extra light into the channel Material used: PETG or higher is recommended if printing higher temp materials Standard: 360g +/- Sliding: 425g +/- Backer: 210g +/- Settings: Recommended: 0.2mm layer heights, 3 walls, 10-15% gyroid infill, 4 T/B layers, 75mm/s outside layer speed for better appearance Same as original but with an added LED channel, LED diffuser and LED top cap to add into the P1P frame. Works with the X1C glass top and you'll just need to get the TPU pads from the original file! Added back channel hole for the X1 series as well to make it compatible with both units After print: There are x6-7 0.4x0.8mm interior supports on the bottom to support the sliders during printing. Gently apply pressure from the inside back along the bottom of sliders. You'll hear several pops as they are broken free Use a small screwdriver or tweezers to apply gentle pressure pushing on the ends to help loosen the slides if they are being difficult There is an internal locking mechanism in the bottom but there is top and bottom clearance to allow it to slide. Slide the pieces together and install onto your machine! Other pieces are coming soon and will be updated in the respective folders once completed Associated Files: Top bracket for Glass or Enclosure: https://www.printables.com/model/352439-bambu-p1p-x1-top-glass-adapter Revisions: Dec25: adjusted tolerances for fitting the keys together added a thicker walls for top and filled in the sides for a complete glass top. raised the exterior rib 2mm to give the glass more area to be covered on the side Dec 26: Added an Alpha phased version with sliding panels to the work file, tolerances have been tested to work and moving forward to production printing. Added locking channels to keep the sliders in place and help with vibrations moving the sliders open or closed. added more room for the top glass and other printed parts. Created new pieces to attach as the originals were very stiff and often broe while trying to connect them Added a back of P1P Top support to help hold it in place, it's a temporary piece until a full enclosure and side panels are created in the future Dec 28: Added.3mf files of the builds with suggested settings Cleaned up the files for the Sliders and adjusted the Backer pieces to fit better Changed the status of the files to Beta as they are printable and should be error free based on previous prints and digital revisions Jan 9: Uploaded the slider v3 files after PLA testing have been successful removed the locking key on sliders as it was occasionally fusing or not giving the proper effect and will look into another solution in the future if requested Wide version partially uploaded and will post the LED portions once they are completed Jan 16: Updated the (W) file for extra LED slot holes to better allow light into the Chamber Apr 10: Added a Step file for the Igloo enclosure and its smaller top glass sizing as a step file for easier adjustments to your overall cut and thickness June 18 uploaded the W-Diffusers (sorry for the wait as its been a busy few months) Sept 27: revised a few overhangs and did a little cleanup new files uploaded for anyone who wishes to work on it further