About this 3D model

Many have attempted it, yet none have achieved it until now. Today marks the grand market launch. First, I would like to extend my deepest gratitude to the entire team, who have dedicated countless weeks and hours to the development of this project. It has been meticulously designed, engineered, constructed, and tested. Their efforts have been rewarded, as it is a resounding success. Furthermore, I want to reiterate that remixing this product design is strictly prohibited. Several reasons underpin this decision. Primarily, there is no justification for remixing this design, as the inclusion of phases or roundings was deliberate and carefully considered. There is no need to add or remove logos, which is why seven distinct downloads are available for your selection. One is the original: 1: Air-Stream-Freezer (it was named so for a specific reason) 2: Bambulab logo with lettering 3: Bambulab logo single 4: Bambulab logo single 5: Bambulab P1S version 6: Bambulab P1P version 7: complete without frills, branding or logo Therefore, there should be a version for every taste. Consequently, as previously mentioned, there is no sensible reason (apart from the desire to adorn oneself with other's achievements for recognition) to remix this product. It is unfortunate that it is likely only a matter of weeks before this design appears for sale on a vast Asian sales platform, mirroring the fate of many designs generously offered for free to everyone on platforms like this one. Should anyone believe that something could be improved, feel free to contact me regarding the matter. We will endeavor to implement your suggestions. We are also diligently working on designing a version for the X1C and X1E. It is recommended to utilize the saved print profile. Additionally, it is advisable to print using ABS. The layer height should be 0.1 with a 0.4 nozzle. A standard support should be positioned at the bottom for the ventilation ring. Everything above this ring, which requires support, can be reliably blocked with a large support blocker, thereby reducing printing time. The print proceeds normally from bottom to top. Should the slicer suggest positioning it at a 45 degree angle, disregard this recommendation and place it flat on the floor. After printing, insert a finger into the ring from above to push the support outwards from top to bottom. Complete. Now simply glue in the two magnets (4x2 and 3x2) and relish the genuine 360-degree ventilation for all future prints. Have fun Many have attempted it, yet none have achieved it until now. Today marks the grand market launch. First, I would like to extend my deepest gratitude to the entire team, who have dedicated countless weeks and hours to the development of this project. It has been meticulously designed, engineered, constructed, and tested. Their efforts have been rewarded, as it is a resounding success. Furthermore, I want to reiterate that remixing this product design is strictly prohibited. Several reasons underpin this decision. Primarily, there is no justification for remixing this design, as the inclusion of phases or roundings was deliberate and carefully considered. There is no need to add or remove logos, which is why seven distinct downloads are available for your selection. One is the original: 1: Air-Stream-Freezer (it was named so for a specific reason) 2: Bambulab logo with lettering 3: Bambulab logo single 4: Bambulab logo single 5: Bambulab P1S version 6: Bambulab P1P version 7: complete without frills, branding or logo Therefore, there should be a version for every taste. Consequently, as previously mentioned, there is no sensible reason (apart from the desire to adorn oneself with other's achievements for recognition) to remix this product. It is unfortunate that it is likely only a matter of weeks before this design appears for sale on a vast Asian sales platform, mirroring the fate of many designs generously offered for free to everyone on platforms like this one. Should anyone believe that something could be improved, feel free to contact me regarding the matter. We will endeavor to implement your suggestions. We are also diligently working on designing a version for the X1C and X1E. It is recommended to utilize the saved print profile. Additionally, it is advisable to print using ABS. The layer height should be 0.1 with a 0.4 nozzle. A standard support should be positioned at the bottom for the ventilation ring. Everything above this ring, which requires support, can be reliably blocked with a large support blocker, thereby reducing printing time. The print proceeds normally from bottom to top. Should the slicer suggest positioning it at a 45 degree angle, disregard this recommendation and place it flat on the floor. After printing, insert a finger into the ring from above to push the support outwards from top to bottom. Complete. Now simply glue in the two magnets (4x2 and 3x2) and relish the genuine 360-degree ventilation for all future prints. Have fu