About this 3D model

The AOS ProBoxXL Organizer is a all-in-one transport box, organizer and foldable dice tray and compatible with the tabletop game Age of Sigmar. Dimension (xyz): 260 x 162 x 53 mm (folded) The ProBoxXL is the larger version of the original ProBox. It's a dice tray and a practical storage and dice box for your tabletop gaming accessories. The box has a dimension of 260 x 162 x 53 mm and this size is almost doubled when activating the dice-tray mode :) It's recommened to glue an appropriate felt or similar on the inner surface so you can roll your dice as a PRO. All XL organizer inserts in the ProBox XL are interchangeable and can also be purchased individually here. The AOS organizer comes with a dedicated printable set of gaming equipment for your game. Content & description ProBoxXL ProBoxXL_body_top: upper part of the box, it's recommenend to glue a felt on the surface ProBoxXL_body_bottom: lower part of the box, it's recommenend to glue a felt on the surface ProBoxXL_body_top_diceplate: top body part but with the diceplate included ProBoxXL_body_bottom_diceplate: lower body part but with the diceplate included ProBoxXL_diceplate: separate diceplate for the top and bottom part of the ProBoxXL if you want to print it with another material (e.g. TPU) or color ProBoxXL_hinge_multipart: set of hinges as a strong multipart version. You need to glue the hinge part locker with a little bit of superglue ProBoxXL_slidingclosure: set of sliding closure AOS Organizer Insert ProBoxXL_AOS_Organizer: organizer insert for the ProBoxXL ProBoxXL_AOS_Organizer_Box: small box for the organizer Magnetic_Battle_Gauge_V1 (top and bottom): Magnetic battle gauge for 0.5, 1, 3, 6, 7, 8, 9, 10, and 12 (3+9) inch measurements ProBoxXL_AOS_Organizer_3inchtemplate_multicolor: Range rulers for 0.5, 1, and 3 inches (NEODYM MAGNETS NEEDED / multicolor: for mulitcolor print you need to split the .stl into parts with your slicer) ProBoxXL_AOS_Organizer_CPToken: CP marker (multicolor version: for mulitcolor print you need to split the .stl into parts with your slicer) ProBoxXL_AOS_Organizer_ObscuringToken: Obscuring marker (multicolor: for mulitcolor print you need to split the .stl into parts with your slicer) AOS_Token_DeBuff_Set: 27 DeBuff Token (e.g. +1 To Hit, Strike First,...) available as a set or 27 single .stl files AOS_Token_Buffboard: Token holder for 10 DeBuff token (printed 3x) AOS_Token_Aura: 3,6,9 and 12 inch Aura token for the DeBuff token Update: +16 DeBuff Token set "Lord of Change" Assembly ProBoxXL Video of the ProBox (similar to the ProBoxXL)youtube.com/watch?v=WKvaHR6r5nY Note: In the video, I'm using two sheets of self-adhesive felts but you can also use any other felt or material. Or just print the box in a version with a roughened surface without the need of any material to use. Superglue Opt. felt for dice rolling (238 x 140mm)It's recommened to use some sort of felt for the inner side of the ProBoxXL for a smooth dice rolling. So this is the first step: Glue the felt on the inner sides. As an alternative, you can print the "diceplate" versions of the ProBoxXL with an in-built roughened inner surfaces or just print 2 diceplates (e.g. with TPU) and glue it on the surface. As a second step you would need to prepare the hinges and glue it to the sides of the ProBoxXL Magnetic Battle Gauge 5 NEODYM magnets needed: 1x 10x2mm (or 2x 10x1mm) + 4x 10x1mm Glue the magnets into the holes and take care of the magnetic direction! :) Use a little grease on the parts that slide into each other. As you don't always want to pull out the upper part, I have added a stopper. That also means that you need to push the upper part into the lower part at an angle of about 10-20° AFTER you have inserted the magnets.